Light Diffraction of Aligned Polymer Fibers Periodically Dispersed by Phase Separation of Liquid Crystal and Polymer

We have confirmed light diffraction of aligned polymer fibers obtained by a phase separation of an anisotropic-phase solution of liquid crystal and polymer. He—Ne laser light passing through the polymer fibers was scattered in the axis vertical to the fibers, and had two peaks of light intensity symmetrical to the center of the transmitting laser spot. The two peaks were found to be caused by light diffraction due to the periodic polymer-fiber dispersion because the peaks corresponded to values calculated by intervals between the fibers. The periodical fiber networks are considered to be formed by anisotropic spinodal decomposition. This effect can be used to measure the dispersion order of the polymer fibers. © 2004 The Optical Society of Japan     

Completely biodegradable composites of poly(propylene carbonate) and short,lignocellulose fiber Hildegardia populifolia

The composites of biodegradable poly(propylene carbonate) (PPC) reinforced with short Hildegardia populifolia natural fiber were prepared by melt mixing followed by compression molding. The mechanical properties, thermal properties, and morphologies of the composites were studied via static and dynamic mechanical measurements, thermogravimetric analysis, and scanning electron microscopy (SEM) techniques, respectively. Static tensile tests showed that the stiffness and tensile strength of the composites increased with an increasing fiber content. However, the elongation at break and the energy to break decreased dramatically with the addition of short fiber. The relationship between the experimental results and the compatibility or interaction between the PPC matrix and fiber was correlated. SEM observations indicated good interfacial contact between the short fiber and PPC matrix. Thermogravimetric analysis revealed that the introduction of short Hildegardia populifolia fiber led to a slightly improved thermooxidative stability of PPC. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 666–675, 2004     

光纤光栅选频掺Yb3+双包层光纤激光器

利用相位掩模法 ,在D形内包层掺Yb3 双包层光纤一端直接写制出Bragg光栅 ,用作双包层光纤激光器的输出腔镜 .试验得到了线宽为 0 196nm ,波长为 10 5 8 2nm ,最高输出功率为 5 70mW的稳定激光输出 ,解决了激光器中模式竞争造成的输出不稳定现象 .从速率方程出发 ,对激光器的输出功率与抽运功率、光栅反射率的关系以及最佳光纤长度进行了理论分析 ,结果与实验符合很好     

闪烁光纤在γ射线辐照下部分特性的蒙特卡罗模拟

 闪烁光纤在射线成像方面的应用越来越广泛。为了进一步了解闪烁光纤在射线辐照下的基本特性，基于蒙特卡罗方法，利用计算机模拟分析了γ射线在闪烁光纤中的好事例率与光纤长度及射线能量的关系，能量沉积效率与光纤长度及射线能量的关系。此项工作对于闪烁光纤阵列在射线成像，剂量场测量等方面的研究很有价值。     

用楔形柱面光纤微透镜耦合的1.3μm SOA组件

运用激光模式耦合理论分析了半导体光放大器(SOA)与单模通信光纤的连接损耗,并设计制作了楔形柱面光纤微透镜用来实现两者的模斑匹配,有效地降低了器件的光耦合损耗.本文介绍了楔形柱面光纤微透镜耦合的1.3 μm半导体光放大器(SOA)组件及其制作方法.该组件的最大增益不小于14 dB,其偏振灵敏度小于1 dB,增益波动不大于0.5 dB.     

两段级联掺铒光纤放大器的优化研究

基于Giles模型,研究了980 nm和1480 nm泵浦的两段级联掺铒光纤放大器(EDFA)的设计,得出了掺铒光纤(EDF)的最佳长度和光隔离器的最佳位置随泵浦功率和信号功率的变化关系.比较980 nm和1480 nm泵浦的两段级联EDFA,可以发现,前者的最佳EDF长度短,而光隔离器最佳位置距EDFA输入端远.     

Nd~(3+):YAG激光的光纤传输

首先叙述了光纤传输Nd~(3+): YAG激光的优点,接着分析了不同光纤和其传输Nd~(3+): YAG激光的特点。然后通过对光纤传输系统各部分的分析与设计,结合实际,设计了光纤耦合机构。最后,对来自于工件反射光问题提出了解决方案。     

Optical bistability in an all-optical fiber nonlinear fabry-perot resonator with linear absorption

An all-optical fiber nonlinear Fabry-Perot resonator is proposed. The steady-state model for describing this resonator is developed. The transmission and refection bistabilities are shown numerically. Our results show that the bistability in this system is similar to that in a normal nonlinear Fabry-Perot etalon, except that the characteristics of the bistability can be changed not only by the cavity length but also by the phase shifts of the fiber loop mirrors.     

折射率温敏式光纤温度传感器的理论模型

提出了折射率温敏式光纤温度传感器的理论模型，包括子午光线和偏射光线的影响，讨论了多模光纤的弯曲损耗，理论的分析和结果与实验相当一致。     

用紫外光直接在光纤内写入布拉格反射光栅的实验研究

用紫外光直接在光纤内写入布拉格反射光栅的实验研究杜卫冲谭华耀＊刘颂豪华南师范大学，激光生命科学研究所，广州５１０６３１＊香港理工大学，电机系自１９８９年Ｍｅｌｔａｚ［１］首次提出采用两束波长位于掺Ｇｅ－石英光纤吸收带内的相干紫外激光相干涉，从侧面照射...